I've played for 3 weeks now to install my hauppage dvb card to stream tv over my network,
(hauppage nova-s-plus)
but no luck yet,
I have PVR-150 on same box which is working fine.
here is my dmesg
Code: Select all
Linux version 2.6.18-1.2849.fc6 (brewbuilder@hs20-bc2-4.build.redhat.com) (gcc v ersion 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Fri Nov 10 12:45:28 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7b0000 (usable)
BIOS-e820: 000000003f7b0000 - 000000003f7c0000 (ACPI data)
BIOS-e820: 000000003f7c0000 - 000000003f7f0000 (ACPI NVS)
BIOS-e820: 000000003f7f0000 - 000000003f800000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 260016
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 30640 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 ACPIAM ) @ 0x000faf80
ACPI: RSDT (v001 A M I OEMRSDT 0x10000610 MSFT 0x00000097) @ 0x3f7b0000
ACPI: FADT (v002 A M I OEMFACP 0x10000610 MSFT 0x00000097) @ 0x3f7b0200
ACPI: MADT (v001 A M I OEMAPIC 0x10000610 MSFT 0x00000097) @ 0x3f7b0390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000610 MSFT 0x00000097) @ 0x3f7c0040
ACPI: DSDT (v001 A0551 A0551036 0x00000036 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f800000:c0380000)
Detected 2800.253 MHz processor.
Built 1 zonelists. Total pages: 260016
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07af000 soft=c078f000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1023696k/1040064k available (2139k kernel code, 15648k reserved, 866k da ta, 244k init, 122560k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5602.61 BogoMIPS (lpj=2801306)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 0 0000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000180 0000641d 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07b0000 soft=c0790000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5599.49 BogoMIPS (lpj=2799746)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 0 0000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000180 0000641d 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
Total of 2 processors activated (11202.10 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
migration_cost=520
checking if image is initramfs... it is
Freeing initrd memory: 2245k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: f7f00000-fbffffff
PREFETCH window: f0000000-f6ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1169191287.949:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key CA06D81CB13FD94
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not pres ent [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not pres ent [20060707]
ACPI: Getting cpuindex for acpiid 0x4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
hdd: LITE-ON DVD SHD-16P1S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 244k freed
Write protecting the kernel read-only data: 386k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000c400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000c800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xf7e7bc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA000 irq 169
ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0xA008 irq 169
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ata_piix
usb 1-1: device not accepting address 2, error -71
ATA: abnormal status 0x7F on port 0xA807
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
input: USB Optical Mouse USB Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [USB Optical Mouse USB Optical Mouse] on usb-0000:00: 1d.0-1
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input2
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
kjournald starting. Commit interval 5 seconds
EXT3-fs: dm-0: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 4391606
ext3_orphan_cleanup: deleting unreferenced inode 61933112
ext3_orphan_cleanup: deleting unreferenced inode 4391637
ext3_orphan_cleanup: deleting unreferenced inode 61933121
ext3_orphan_cleanup: deleting unreferenced inode 61933120
ext3_orphan_cleanup: deleting unreferenced inode 4391603
EXT3-fs: dm-0: 6 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1169191294.951:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input3
Linux video capture interface: v2.00
hdd: ATAPI 48X DVD-ROM drive, 1727kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:01:0d.0[A] -> GSI 23 (level, low) -> IRQ 193
skge 1.6 addr 0xf7ff8000 irq 193 chip Yukon-Lite rev 9
skge eth0: addr 00:18:f3:08:a7:58
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp 0000:01:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:01:0b.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 201
eth1: RealTek RTL8139 at 0xf89b4c00, 00:13:49:24:4e:00, IRQ 201
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
ivtv: no version for "struct_module" found: kernel tainted.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.8.2 (tagged release) loading
ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload 686 REGPARM 4KSTACKS gcc- 4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 17 (level, low) -> IRQ 209
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
cx2388x v4l2 driver version 0.0.6 loaded
cx2388x alsa driver version 0.0.6 loaded
sd 0:0:0:0: Attached scsi generic sg0 type 0
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tveeprom 0-0050: The eeprom says no radio is present, but the tuner type
tveeprom 0-0050: indicates otherwise. I will assume that radio is present.
tveeprom 0-0050: Hauppauge model 26589, rev C9A5, serial# 9472820
tveeprom 0-0050: tuner model is TCL MPE05-2 (idx 105, type 38)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x 74)
tveeprom 0-0050: audio processor is CX25843 (idx 37)
tveeprom 0-0050: decoder processor is CX25843 (idx 30)
tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-150
tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
ivtv0: Registered device radio0 for encoder radio
tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
ACPI: PCI Interrupt 0000:01:0a.1[A] -> GSI 21 (level, low) -> IRQ 217
CORE cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37, autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom 1-0050: Hauppauge model 92001, rev B1B1, serial# 416296
tveeprom 1-0050: MAC address is 00-0D-FE-06-5A-28
tveeprom 1-0050: tuner model is Conexant_CX24109 (idx 111, type 4)
tveeprom 1-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 1-0050: audio processor is CX883 (idx 32)
tveeprom 1-0050: decoder processor is CX883 (idx 22)
tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=92001
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input4
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
cannot find the slot for index 0 (range 0-0)
Intel ICH: probe of 0000:00:1f.5 failed with error -12
ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 217
cx88[0]/0: found at 0000:01:0a.0, rev: 5, irq: 217, latency: 64, mmio: 0xf800000 0
cx88[0]/0: registered device video1 [v4l2]
cx88[0]/0: registered device vbi1
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:01:0a.2[A] -> GSI 21 (level, low) -> IRQ 217
cx88[0]/2: found at 0000:01:0a.2, rev: 5, irq: 217, latency: 64, mmio: 0xfa00000 0
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.4 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across: 2031608k
ip6_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_rea chable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead.
skge eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized i915 1.5.0 20060119 on minor 0
usb 2-2: USB disconnect, address 2
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input5
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input6
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 3
usb 2-2: new low speed USB device using uhci_hcd and address 4
usb 2-2: new low speed USB device using uhci_hcd and address 5
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input7
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input8
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 5
usb 2-2: new low speed USB device using uhci_hcd and address 6
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input9
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input10
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 6
usb 1-1: USB disconnect, address 4
[root@localhost ~]# cls
-bash: cls: command not found
[root@localhost ~]# clear
[root@localhost ~]# cls
-bash: cls: command not found
[root@localhost ~]# clear
[root@localhost ~]# dmesg
Linux version 2.6.18-1.2849.fc6 (brewbuilder@hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Fri Nov 10 12:45:28 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f7b0000 (usable)
BIOS-e820: 000000003f7b0000 - 000000003f7c0000 (ACPI data)
BIOS-e820: 000000003f7c0000 - 000000003f7f0000 (ACPI NVS)
BIOS-e820: 000000003f7f0000 - 000000003f800000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 260016
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 30640 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 ACPIAM ) @ 0x000faf80
ACPI: RSDT (v001 A M I OEMRSDT 0x10000610 MSFT 0x00000097) @ 0x3f7b0000
ACPI: FADT (v002 A M I OEMFACP 0x10000610 MSFT 0x00000097) @ 0x3f7b0200
ACPI: MADT (v001 A M I OEMAPIC 0x10000610 MSFT 0x00000097) @ 0x3f7b0390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000610 MSFT 0x00000097) @ 0x3f7c0040
ACPI: DSDT (v001 A0551 A0551036 0x00000036 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f800000:c0380000)
Detected 2800.253 MHz processor.
Built 1 zonelists. Total pages: 260016
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07af000 soft=c078f000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1023696k/1040064k available (2139k kernel code, 15648k reserved, 866k data, 244k init, 122560k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5602.61 BogoMIPS (lpj=2801306)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000180 0000641d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07b0000 soft=c0790000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5599.49 BogoMIPS (lpj=2799746)
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000641d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20000000 00000000 00000180 0000641d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
Total of 2 processors activated (11202.10 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
migration_cost=520
checking if image is initramfs... it is
Freeing initrd memory: 2245k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: f7f00000-fbffffff
PREFETCH window: f0000000-f6ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1169191287.949:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key CA06D81CB13FD94
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
hdd: LITE-ON DVD SHD-16P1S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 244k freed
Write protecting the kernel read-only data: 386k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000c400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000c800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xf7e7bc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA000 irq 169
ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0xA008 irq 169
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ata_piix
usb 1-1: device not accepting address 2, error -71
ATA: abnormal status 0x7F on port 0xA807
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
input: USB Optical Mouse USB Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [USB Optical Mouse USB Optical Mouse] on usb-0000:00:1d.0-1
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input1
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input2
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
kjournald starting. Commit interval 5 seconds
EXT3-fs: dm-0: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 4391606
ext3_orphan_cleanup: deleting unreferenced inode 61933112
ext3_orphan_cleanup: deleting unreferenced inode 4391637
ext3_orphan_cleanup: deleting unreferenced inode 61933121
ext3_orphan_cleanup: deleting unreferenced inode 61933120
ext3_orphan_cleanup: deleting unreferenced inode 4391603
EXT3-fs: dm-0: 6 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1169191294.951:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input3
Linux video capture interface: v2.00
hdd: ATAPI 48X DVD-ROM drive, 1727kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:01:0d.0[A] -> GSI 23 (level, low) -> IRQ 193
skge 1.6 addr 0xf7ff8000 irq 193 chip Yukon-Lite rev 9
skge eth0: addr 00:18:f3:08:a7:58
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp 0000:01:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:01:0b.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 201
eth1: RealTek RTL8139 at 0xf89b4c00, 00:13:49:24:4e:00, IRQ 201
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
ivtv: no version for "struct_module" found: kernel tainted.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.8.2 (tagged release) loading
ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload 686 REGPARM 4KSTACKS gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 17 (level, low) -> IRQ 209
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
cx2388x v4l2 driver version 0.0.6 loaded
cx2388x alsa driver version 0.0.6 loaded
sd 0:0:0:0: Attached scsi generic sg0 type 0
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tveeprom 0-0050: The eeprom says no radio is present, but the tuner type
tveeprom 0-0050: indicates otherwise. I will assume that radio is present.
tveeprom 0-0050: Hauppauge model 26589, rev C9A5, serial# 9472820
tveeprom 0-0050: tuner model is TCL MPE05-2 (idx 105, type 38)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 0-0050: audio processor is CX25843 (idx 37)
tveeprom 0-0050: decoder processor is CX25843 (idx 30)
tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-150
tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
ivtv0: Registered device radio0 for encoder radio
tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
ACPI: PCI Interrupt 0000:01:0a.1[A] -> GSI 21 (level, low) -> IRQ 217
CORE cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom 1-0050: Hauppauge model 92001, rev B1B1, serial# 416296
tveeprom 1-0050: MAC address is 00-0D-FE-06-5A-28
tveeprom 1-0050: tuner model is Conexant_CX24109 (idx 111, type 4)
tveeprom 1-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 1-0050: audio processor is CX883 (idx 32)
tveeprom 1-0050: decoder processor is CX883 (idx 22)
tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=92001
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input4
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
cannot find the slot for index 0 (range 0-0)
Intel ICH: probe of 0000:00:1f.5 failed with error -12
ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 217
cx88[0]/0: found at 0000:01:0a.0, rev: 5, irq: 217, latency: 64, mmio: 0xf8000000
cx88[0]/0: registered device video1 [v4l2]
cx88[0]/0: registered device vbi1
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:01:0a.2[A] -> GSI 21 (level, low) -> IRQ 217
cx88[0]/2: found at 0000:01:0a.2, rev: 5, irq: 217, latency: 64, mmio: 0xfa000000
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.4 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
ip6_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_reachable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead.
skge eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized i915 1.5.0 20060119 on minor 0
usb 2-2: USB disconnect, address 2
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input5
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input6
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 3
usb 2-2: new low speed USB device using uhci_hcd and address 4
usb 2-2: new low speed USB device using uhci_hcd and address 5
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input7
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input8
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 5
usb 2-2: new low speed USB device using uhci_hcd and address 6
usb 2-2: configuration #1 chosen from 1 choice
input: USB Keyboard as /class/input/input9
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.1-2
input: USB Keyboard as /class/input/input10
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.1-2
usb 2-2: USB disconnect, address 6
usb 1-1: USB disconnect, address 4
[root@localhost ~]#
here is my lspci
Code: Select all
[root@localhost ~]# lspci
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
01:09.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
01:0a.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
01:0a.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:0a.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:0a.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:0d.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
lspci -v
Code: Select all
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8157
Flags: bus master, fast devsel, latency 0
Memory at efc00000 (32-bit, prefetchable) [size=4M]
Capabilities: [e4] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, fast devsel, latency 0, IRQ 177
Memory at e0000000 (32-bit, prefetchable) [size=128M]
Memory at f7e80000 (32-bit, non-prefetchable) [size=512K]
I/O ports at d800 [size=8]
Capabilities: [d0] Power Management version 1
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 177
I/O ports at c400 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 185
I/O ports at c800 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 169
I/O ports at d000 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 177
I/O ports at d400 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 193
Memory at f7e7bc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7f00000-fbffffff
Prefetchable memory behind bridge: f0000000-f6ffffff
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
Flags: bus master, medium devsel, latency 0, IRQ 169
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at fc00 [size=16]
Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. P4P800 SE Mainboard
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 169
I/O ports at b400 [size=8]
I/O ports at b000 [size=4]
I/O ports at a800 [size=8]
I/O ports at a400 [size=4]
I/O ports at a000 [size=16]
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8227
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at c000 [size=256]
I/O ports at b800 [size=64]
Memory at f7e7b800 (32-bit, non-prefetchable) [size=512]
Memory at f7e7b400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
01:09.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. Unknown device b7f1
Flags: bus master, medium devsel, latency 64, IRQ 209
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
01:0a.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: Hauppauge computer works Inc. Nova-S-Plus DVB-S
Flags: bus master, medium devsel, latency 64, IRQ 217
Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Unknown device 9202
Flags: bus master, medium devsel, latency 64, IRQ 217
Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
01:0a.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Unknown device 9202
Flags: bus master, medium devsel, latency 64, IRQ 217
Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
01:0a.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
Subsystem: Hauppauge computer works Inc. Unknown device 9202
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: ZyXEL Communication Corporation Unknown device 3303
Flags: bus master, medium devsel, latency 64, IRQ 201
I/O ports at e800 [size=256]
Memory at f7fffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
01:0d.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193
Memory at f7ff8000 (32-bit, non-prefetchable) [size=16K]
I/O ports at e400 [size=256]
Expansion ROM at f4000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
[root@localhost ~]#
Code: Select all
Unable to open 'dvb://'