Amino A130 1080P/1080I Configuration

[koffieschaap]

Hello Everyone,

i am currently building up a page for the Amino 130 HD Box. everything is running well at 720P.
When i try to change the settings towards 1080 (which my screen CAN take on HDMI and DVI input) the device does not boot with the following console messages:

Code: Select all

Jan 1 00:00:23:261224 AMINET user.info syslog: --homepage http://stb.amino.eimc.lan Jan 1 00:00:23:268044 AMINET user.err syslog: Failed to open GFX fb[1] device 19 Jan 1 00:00:23:270539 AMINET user.info syslog: AMI_WM size h=0, w=0 Jan 1 00:00:23:311681 AMINET user.warn syslog: Respawning '/bin/ami_wm_fb0' (0 times in 0s) Jan 1 00:00:23:331088 AMINET user.err syslog: targetFB = 0 Jan 1 00:00:23:344621 AMINET user.err syslog: Failed to open GFX fb[1] device 19 Jan 1 00:00:23:346083 AMINET user.err syslog: server : AMIWM_SOCKET - '/tmp/ami_wm.sock' Jan 1 00:00:23:392145 AMINET user.warn syslog: Respawning '/mnt/nv/opera' (10 times in 5s) Jan 1 00:00:23:392699 AMINET user.err syslog: **************************************** Jan 1 00:00:23:393291 AMINET user.err syslog: CRITICAL FAILURE, '/mnt/nv/opera' IS FAILING TO RESPAWN, FAILED 10 TIMES OVER 10 SECONDS Jan 1 00:00:23:393810 AMINET user.err syslog: REBOOTING! Jan 1 00:00:23:394332 AMINET user.err syslog: **************************************** Jan 1 00:00:23:482742 AMINET daemon.info init: ^MThe system is going down NOW !!Waited for DMA Rx to settle. Exited after 0 iterations, status now 0x00600100 The system is going down NOW !! Jan 1 00:00:23:484485 AMINET syslog.info System log daemon exiting on signal 15. Exiting Syslogd! Jan 1 00:00:23 dhcpcd[1069]: terminating on signal 15 Terminated Stopping networking scripts End of DHCP script Stopping NTPclient Daemon Stopping STBrcd kill: 59: %m Restarþ

this is with the settings in netconf file: OUTPUT_RESOLUTION="HF1080I59"
and setting in setting file: GFX_RESOLUTION="HD1080"

anbyone know how this can be resolved?



Koffie

[McLeodUA]

Amino 130 does not support 1080p.
Maximum supported resolution is 1080i.
In this case I believe that 720p for video output is much better cause 1080i is 1080/2=540 lines, and 720p is 720 lines.
Draw a conclusion yourself.

[bigorniax]

Hi,

I need to use GFX at HD1080 and the OUTPUT at 720p.

Do you know how to do it ¿?

Please help!!

BX

[stb]

There are several ways to do so.

Remote using STBremoteconf:

Code: Select all

STBremoteconf "IP" SETCONFIG SETTINGS.GFX_RESOLUTION HD1080

(but i believe the highest possible GFX is 720p, so you use HD720 instead of HD1080)

Code: Select all

STBremoteconf "IP" OUTRES 720p

Using Telnet:

on the box use:

Code: Select all

libconfig-set SETTINGS.GFX_RESOLUTION HD1080

Code: Select all

libconfig-set NORFLASH.OUTPUT_RESOLUTION HD720P50

(50 is the Framerate)

I consider it the best solution to set both to 720p.