Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

For questions and discussion that is NOT (I repeat NOT) specific to a certain Operating System.
wernerhp
New Cone
New Cone
Posts: 2
Joined: 10 Oct 2007 13:08

Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby wernerhp » 12 Oct 2007 11:57

as you can see from the subject my AmiNET 110 STB is stuck on a screen that sais Loading... (on the TV)

i managed to login using root and root2root. i think the place where i went wrong is...it was rebooting all the time, so i killed a couple of processes until it stopped rebooting...then i rebooted it and now it's stuck on this Loading screen... I connected via telnet...when scanning my network for IPs the STB doesn't seem to have one in the local range. any suggestions?

quauhtlimtz
Blank Cone
Blank Cone
Posts: 10
Joined: 05 Jan 2008 23:37

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby quauhtlimtz » 18 Jan 2008 18:16

I have the same problem too. You got a solution already?

Thanks.

Maulkin
New Cone
New Cone
Posts: 7
Joined: 14 Jan 2008 14:36

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby Maulkin » 12 Feb 2008 23:56

Sounds like you tried to upgrade it and it went wrong. Are you sure it's getting a dhcp lease?

yuanzhoulv
New Cone
New Cone
Posts: 2
Joined: 26 Apr 2009 15:53

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby yuanzhoulv » 26 Apr 2009 16:13

try this. build an amino serial cable (see below), connect to it with a terminal, hit ENTER when it starts and prompts to hit ENTER to leave normal operation. then type
bootos AMInet.img
and see if it works.

if this results in a functional Amino, just create a file called !poweron (with the exclamation point) in /mnt/nv (the vi editor is available) and in it put the bootos AMInet.img line in it.

be careful not to create other files, any unrecognised filenames in /mnt/nv (including things you back up) will cause the Amino to freak out again.

--
serial cable:

J7 connector on the Aminet 110:
PIN 1 (square) - VCC
PIN 2 - TX
PIN 3 - RX
PIN 4 - GROUND

PC serial port DB9 connector:
PIN 2- RX
PIN 3 - TX
PIN 5 - GROUND

1. Jumper (short) pins 4,6 on the PC side
2. Jumper (short) pins 7,8 on the PC side
3. Build a TTL-RS232 signal level converter between the PC serial port's TX/RX and the Amino's RX/TX, respectively. This simple one worked beautifully for me
http://www.sparkfun.com/datasheets/Prot ... ter-v2.pdf
4. Connect at 115200,N,8,1.

That's it!

pseudo_intellectual
New Cone
New Cone
Posts: 2
Joined: 27 Nov 2009 22:59

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby pseudo_intellectual » 27 Nov 2009 23:13

try this. build an amino serial cable (see below), connect to it with a terminal, hit ENTER when it starts and prompts to hit ENTER to leave normal operation. then type
bootos AMInet.img
and see if it works.
Thanks for posting this info as it has enabled me to get into this Aminet125 box I picked up at a thrift store for $2. I'm pretty much just poking around with the box to see if there's anything useful I can do with it. Heck, if I knew where the JTAG pins were, I'd make it an experiment board for my embedded software aspirations.

My problem, however, is that it won't let me into the console when I press enter at the prompt. I thought that I had incorrectly wired my serial interface, but if I touch the RX and TX pins together, my key presses echo back to me. That indicates to me that at least my cable is built correctly, but I am wondering if I have either damaged the Aminet125's UART (oops!) while probing or if I have somehow missed something not mentioned here. If it helps, here is my output:

Code: Select all

Platform setup...done *LOAD* Loading IntActOSSecure ROM start vectors at 81105990 Amino Communications IntActOS-32 v1.45 on AMINET125 with 128Mb RAM Processor: ARM 926EJ-S running at 300.000 MHz 81140000 ASB v1.22 temp.totalsize 01E00000 temp.usablesize 01E00000 mediainfo.totalsize 02000000 = 32MBytes 81148000 FIL v1.36 81158000 VUL v2.00 81160000 ETH v1.30 81168000 CPT v1.00 AMINET125 BOOT ROM VERSION 1.34.16 TV system = NTSC-M Output format = CVBS-LC Boot ROM has not identified hardware - assuming A125 mode=00000007 channel=132 NX=8611 bits=880021A3 iic write status: 00000000 multicast booting Using MAC address 00:02:02:15:41:65 Ethernet link down Ethernet: Auto-MDIX Hit ENTER to stop normal operation ... temp.totalsize 01E00000 temp.usablesize 01E00000 mediainfo.totalsize 02000000 = 32MBytes 237x49 720x480 Starting cold boot sequence ... 00000000 Sending DHCP Discover Ethernet transmit failed - link down flashled: major=00000002 , minor=00000003 Multicast group of zero - retry later Failed, so retrying..
Based on the above output, should I have been able to enter the "I>" prompt by pressing ENTER? If so, and assuming that I did in fact kill the UART, is it possible to at least configure a DHCP server to use the currently flashed OS instead of trying to TFTP a new one? I'm going out on a limb here, but I'm sure that will be usesless to ask for a software image. (I'd love to be wrong about this, by the way...)

Manishp
New Cone
New Cone
Posts: 1
Joined: 15 Feb 2010 09:31

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby Manishp » 15 Feb 2010 09:41

Hi, I am facing the same problem , that STB is not accepting "Enter" key through Hyper Terminal. Please anyone suggest what is the problem?

Regards,

akyprian
New Cone
New Cone
Posts: 2
Joined: 18 Feb 2010 11:14

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby akyprian » 18 Feb 2010 12:15

Hi all,

I am facing a similar problem. Hitting enter does not have any effect. Here is what I get on my console:

Code: Select all

Initialising NOR Flash. Amino Communications IntActOS-32 v1.44 on AMINET11x with 32Mb RAM Processor: 51510950 running at 252.000 MHz 00140000 ASB v1.22 00148000 FIL v1.36 00150000 VUL v1.14 00158000 ETH v1.26 00168000 CPT v1.00 AMINET11x BOOT ROM VERSION 1.32.18 TV system = PAL-I Output format = CVBS-RGBON Setting DENC0_CR1 to 91000040 Setting DENC1_CR1 to 91001F40 Setting DENCMUX to 3E000000 iic write status: 00000000 multicast booting PHY=LAN83C183 (LAN91C111 Internal) SMC91C11xFD(rev:2) at 70100300 IRQ:25 MEMSIZE:8192 ADDR: 00:02:02:10:50:AC PHY auto-negotiate timed out flashled: major=00000001 , minor=00000001 bootos AMINET.img AMINET.img
Has anybody found a solution, please. Your feedback is greatly appreciated

Regards,

pseudo_intellectual
New Cone
New Cone
Posts: 2
Joined: 27 Nov 2009 22:59

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... scree

Postby pseudo_intellectual » 18 Feb 2010 15:51

It's good to see that I'm not the only one that has this problem, as it's reassuring to know I may not have damaged the serial port as I had initially thought.

For those familiar with the debug cable on these boxes: is there anything special about it apart from using an RS232 driver to convert the RX and TX signals from 3.3v? This is pretty much all I am doing to interface the AmiNET STB to the computer's erial port. I remember reading Amino's documentation on this and didn't see anything, but that was quite a few months ago.

Perhaps it's time to whip this thing out again over the weekend and see if I can figure out what is going on. Is there anyone in the know who can suggest what to do next?

nadeem
New Cone
New Cone
Posts: 5
Joined: 30 Nov 2009 12:48

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... s

Postby nadeem » 10 Jun 2010 16:59

dont worry dear i have solutaion i do same like many time but Enter is not worked but realy i am too much tired when pressing again again trying many time atleast last time i press all keybord and its worked directly to formated a amino wow its amazing but bad luck i do again its not working so keep trying and find correct key .

amkh
New Cone
New Cone
Posts: 1
Joined: 21 Jul 2010 06:53

Re: Amino AmiNET 110 STB (Set Top Box) Stuck on Loading... s

Postby amkh » 21 Jul 2010 08:02

Hi all,
I made a serial cable and connected to the Amino aminet 110 serial port correctly via hyperterminal. But I have another problem: the receiving information from my amino looks like below:
I set the parameters of hyperterminal like this:
Bit Per second:115200
Data Bit:8
Parity : None
Stop Bites:1
Flow control:None

Setting/ Emulation: Auto detect
Font :terminal

Code: Select all

ŽŽáýýþ÷ü¹°þ ÷ý ¿°Žøñûû ûô¾°Žîñ °°¹°¸¸¾¸º¾¹¸°þ ÷ýþ º½º ¾°ýþþñüýö°øñûû úö°ö û°ð ïïîï ï·° °ðþþýû¹·ŽŽî ÷ýþ°ý ó úûõóþŽŽáýýþ÷ü¹°þ ÷ýþ¾°Žøñûû ûô¾°îñ °° ¹°¸¸¾¸º¾¹¹°ü ÷ýþ º½º ¾°ýþþñüýö°øñûû úö°ö û°ð îïîï ï·° °ðþþýû¹·ŽŽì ÷ýþ°ý ó ú ûõóþŽŽáýýþ÷ü¹°þ ÷ýþ¿°Žøñûû úô¾°Žîñþ°°¹°¸¸¾¸»¾¹º°ü ÷ýþ º½ºý¾°ýþþñþýö°øñûû ú ö°ö ú°ð îïîï ï·° °ðþþýû¹·Žì ÷ýþ°ýþó úúõóþŽáýýþ÷þ¹°þ ÷ýþ¾°øñûû úô¾°Žî ñþ°°¹°¸¸¾¸º¾¹»°þ ÷ýþ »½º ¿°ýþþñþýö°øñûû úö°ö ú°ð îïîï ï·° °ðþüýû¹·ŽŽî ÷ýþ°ý ó úú÷óþŽá ýþ÷ü¹°ü ÷ý ¾°
I test above parameters with combination of different values but it get worse. anybody knows what is the problem?


Return to “General VLC media player Troubleshooting”

Who is online

Users browsing this forum: No registered users and 14 guests