DVB-S: setting frontend failed (-1) Invalid argument

[lejeczek]

hi dear all,
short list: 0.9.0-test3 Grishenko, kernel v4l modules compiled from today repo, kernel 2.6.27-0.297.rc5.git2.fc10.x86_64, dvb-s: tt skystar 1 ver. 1.3, and system is fedora rawhide

** vlc command:
vlc -vvv -I dummy --ttl 12 --rc-fake-tty --sout-ts-es-id-pid dvb:// --dvb-adapter 0 --dvb-frequency 1071400 --dvb-srate 22000 --dvb-voltage 18 --dvb-tone auto --programs 9220 --sout '#rtp{dst=10.0.0.100,port=3333,sdp=rtsp://10.0.0.100:1234/test.sdp},select="program=9220"}'

** channel details taken from dvbscan:
Film4:10714:h:0:22000:2346:2347:9220

**vlc errors: -
[00000356] dvb access debug: Opening device /dev/dvb/adapter0/frontend0
[00000356] dvb access debug: Frontend Info:
[00000356] dvb access debug: name = VLSI VES1x93 DVB-S
[00000356] dvb access debug: type = QPSK (DVB-S)
[00000356] dvb access debug: frequency_min = 950000 (kHz)
[00000356] dvb access debug: frequency_max = 2150000 (kHz)
[00000356] dvb access debug: frequency_stepsize = 125
[00000356] dvb access debug: frequency_tolerance = 29500
[00000356] dvb access debug: symbol_rate_min = 1000000 (kHz)
[00000356] dvb access debug: symbol_rate_max = 45000000 (kHz)
[00000356] dvb access debug: symbol_rate_tolerance (ppm) = 0
[00000356] dvb access debug: notifier_delay (ms) = 0
[00000356] dvb access debug: Frontend Info capability list:
[00000356] dvb access debug: inversion auto
[00000356] dvb access debug: forward error correction 1/2
[00000356] dvb access debug: forward error correction 2/3
[00000356] dvb access debug: forward error correction 3/4
[00000356] dvb access debug: forward error correction 5/6
[00000356] dvb access debug: forward error correction 7/8
[00000356] dvb access debug: forward error correction auto
[00000356] dvb access debug: card can do QPSK
[00000356] dvb access debug: End of capability list
[00000356] dvb access debug: trying to tune the frontend...
[00000356] dvb access debug: frequency 1071400 is in IF-band
[00000356] dvb access debug: using inversion=2
[00000356] dvb access debug: using fec=9
[00000356] dvb access debug: using voltage=18
[00000356] dvb access debug: using tone=0
[00000356] dvb access error: DVB-S: setting frontend failed (-1) Invalid argument
[00000356] dvb access error: DVB-S: tuning failed
[00000356] main access warning: no access module matching "dvb" could be loaded
[00000356] main access debug: TIMER module_Need() : 89.514 ms - Total 89.514 ms / 1 intvls (Avg 89.514 ms)
[00000349] main input error: open of `dvb://' failed: could not create access
[00000351] main stream out debug: destroying chain... (name=rtp)

can you guys point my wrong doing? I'm novice thus assume it's rather me.
should mention that have tried a few other channels from that dvbscan output and errors as above
and before, on fedora repo's modules this same too
thank you guys, particularly developers that work on vlc
cheers

** update: it's definitely worth looking to dmesg, ( --dvb-srate 22000(these are M and should be K(+000)
now I'm a bit further but still stuck, here:

[00000356] dvb access debug: DMXSetFilter: DMX_PES_OTHER for PID 8192
[00000356] dvb access error: DMXSetFilter: failed with -1 (Invalid argument)
[00000356] dvb access error: DMXSetFilter failed
[00000356] dvb access debug: Opening device /dev/dvb/adapter0/ca0

cheers

[dionoea]

Hum, I guess that one of you settings is wrong. Could you generate a channels.conf file with dvbscan and open it in VLC to see if that works? (All the parameters should be automatically set from the channels.conf file)